SelectYourLanguage

Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2

Forbo Websites

Select a division
Forbo Group
Forbo Flooring Systems
Forbo Movement Systems
CONTACT FAQ

eurocol
725 ALPHYCOL

725

Alpha-halfydrate based tile adhesive for fixing on anhydrite.

725-alphycol.jpg
  • 725-ec 1 plus licence uk.pdf

    725-ec 1 plus licence uk.pdf

  • 725-safety data sheet uk.pdf

    725-safety data sheet uk.pdf

  • pdf-product-specification.pdf

    pdf-product-specification.pdf

  • dop-declaration-uk.pdf

    dop-declaration-uk.pdf

  • epdfeica- 725 alphycol-uk.pdf

    epdfeica- 725 alphycol-uk.pdf

Product Typification

Alpha-halfydrate based tile adhesive for fixing on anhydrite.
Basis : Alpha-halfydrate mixture with additives and synthetic binders to be mixed with water.
Colour : Off-white.

Product advantages:
  • Specially for anhydrite floors
  • Suitable for underfloor heating systems
  • Favourable open time   
  • High final bond strength
  • Does not deteriorate with age
  • Easy to apply
  • Chromate free
  • Dust reduced
  • Alphy-halfydrate mixture

Performances

Aging : 725 Alphycol does not deteriorate with age.
Consumption : 1.2 - 3.5 kg/m², depending on the smoothness of the subfloor and type of tile.
Curing : Minimum 24 hours, depending on the subfloor and temperature.
Dust factor : < 5% components with a particle of < 2 µm(micrometer)

Application

Application:
  • For fixing ceramic floor tiles and natural stone on calcium suphate (anhydrite) subfloors.
  • Not suitable for outdoor use and/or water pressure (constant moisture-pressure). For this we recommend a watertight and moisture-resistant tile adhesive from Eurocol. 

Working Process

Open time : Place the tiles within 20 to 30 minutes into the wet adhesive, depending on the subfloor and temperature.
Mixing ratio : Add 25 kg of 725 Alphycol to approx. 6.5 litres of water.
Waiting time : After mixing with water wait for a few minutes, stir once again and apply the mixture on the subfloor.
Application temperature : From 5° to 25 °C (temperature of the surrounding as well as the subfloor).
Processing time : Apply the mixture within 90 minutes.
Curing : Minimum 24 hours, depending on the subfloor and temperature.
Storage : Store cool and dry in unopened packaging.
Shelf Life : 12 Months, in unopened packaging. After use close the open packaging well.

* The mentioned values have been established in our laboratory and must be considered as guidelines in view of possible variations in climatic circumstances, subfloor compositions and layer thickness.

Consumption:
1.2 - 3.5 kg/m², depending on the smoothness of the subfloor and type of tile.

Substrate:
  • The anhydrite floor has to be smooth, dry, free from grease, dirt and dust, according to the requirements of DIN 18 352. The floor also must comply with CUR-recommendation 107.
  • Maximum permitted moisture percentage of anhydrite floors is < 1.0% (measured by CM-hygrometer).
  • Adjudge the strength of the top layer of the calcium sulphate subfloor beforehand.
  • In case the top layer has a good strength, tiles can be fixed immediately with 725 Alphycol without a pre-treatment.
  • Sandpaper insufficiently strong top layers, (caused by application, leaks, pollution and present bleeding layers). After sandpapering, remove dust with an industrial vacuum cleaner and prime with 099 Dispersion Primer (minimum drying time  1 hour).
  • When necessary level with 920 Europlan Alphy or 925 Europlan Alphy Direct.
  • In advance always seek our technical data sheets. In doubt about the application ask for technical advice. 


User manual:
  • Preferably mix the adhesive in a clean mixing bucket. A mixing bucket with gypsum residues will lead to a faster bonding of the adhesive.
  • Add 25 kg of 725 Alphycol to approx. 6.5 litres of cool and clean tap water and stir the mortar for 1 minute, by using an electric stirrer (approx. 600 rpm), to a smooth and homogeneous mixture. The stirrer should be free of cement residues!
  • After stirring wait for a few minutes, stir once again and apply the adhesive on the subfloor with the recommended adhesive spreader (see spreading capacity/notched spreader).
  • Press the tiles within 20 to 30 minutes with a shuffling movement into the adhesive. Check regularly to ensure that the back of the tile is in full contact with the adhesive. Remove excess adhesive immediately from the joints.
  • Apply the mixed adhesive must within 90 minutes. Do not add extra water to the bonding mortar!
  • Under normal circumstances, i.e. a temperature of 20 °C and a relative humidity of 65%, the joints may be filled after minimum 24 hours.  

Spreading capacity/notched spreader for powder tile adhesives:

The smoothness of the subfloor and type of tile are determining for the adhesive spreader to be used. Selection of the notched spreader should be made in such way that a minimum adhesive contact of 80% is guaranteed (equally divided over the back of the tile). Check the adhesive contact regularly.

Spreader no. 19, 4x4 mm : Spreading capacity approx. 1.2 kg/m²
Spreader no. 12, 6x6 mm : Spreading capacity approx. 2.0 kg/m²
Spreader no. 13, 8x8 mm : Spreading capacity approx. 2.7 kg/m²
Spreader no. 14, 10x10 mm : Spreading capacity approx. 3.5 kg/m²




Quality and guarantee

Environment and health

Safety and environment : Safety data sheets of Forbo Eurocol products according to EEG-guideline 91/155.
MSDS : For extensive information about safety and environment we refer to our website www.eurocol.nl.





Articles

ArticleDefinitionPackagingEAN-code
725Alphycol25 kg bag8 710345 725019