SelectYourLanguage

Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2

Forbo Websites

Select a division
Forbo Group
Forbo Flooring Systems
Forbo Movement Systems
CONTACT FAQ

eurocol
720 UNICOL

720

High quality floor tile adhesive with a filling ability.

720-unicol.jpg
  • pdf-product-specification.pdf

    pdf-product-specification.pdf

  • dop-declaration-uk.pdf

    dop-declaration-uk.pdf

  • 720-safety data sheet uk.pdf

    720-safety data sheet uk.pdf

  • epdfeica-720 unicol-uk.pdf

    epdfeica-720 unicol-uk.pdf

Product Typification

High quality floor tile adhesive with a filling ability.
Basis : Cement-based powder with additives and a high synthetic binder to be mixed with water.
Colour : White.

Product advantages:
  • Dust reduced
  • Layer thickness from 5 to 15 mm
  • For in- and outdoor use 
  • Flexible
  • Suitable for fixing tiles with a moisture-absorption capacity of 1% or less
  • Suitable for any type of natural stone
  • Fast drying
  • High final bond strength
  • Does not deteriorate with age
  • Easy to apply
  • Low chromate
  • For wall and floor
  • Very suitable for underfloor heating systems

Performances

Aging : 720 Unicol does not deteriorate with age.
Classification : Flexible cement-based tile adhesive, which as far as final bond strength, moisture- and frost-resistance complies with C2TE, according to NEN EN 12004.
Consumption : 2.7-4 kg/m², depending on the smoothness of the subfloor and type of tile.
Curing : After minimum 24 hours the subfloor is passable, after 7 days the floor can be loaded.

Application

Application:
  • For fixing according to the thin or thick-bed method of large sized ceramic wall and floor tiles on almost all stony (irregular) subfloors.
  • Also suitable for all calibrated and non-calibrated natural stone, at what the differences of thickness between the boards must be filled with adhesive
  • Suitable for wall and floor applications and underfloor heating systems.

Working Process

Open time : Place the tiles within 15 to 20 minutes into the wet adhesive, depending on the subfloor and temperature.
Mixing ratio : Add 25 kg of 720 Unicol to 5-5.5 litres of water.
Waiting time : After mixing with water wait for a few minutes, stir once again and apply the mixture on the subfloor.
Application temperature : From 5° to 25 °C (temperature of the surrounding as well as the subfloor).
Processing time : Apply the mixture within 60 minutes.
Curing : After minimum 24 hours the subfloor is passable, after 7 days the floor can be loaded.
Storage : Store cool and dry in unopened packaging.
Shelf Life : 12 Months, in unopened packaging. After use close the open packaging well.

* The mentioned values have been established in our laboratory and must be considered as guidelines in view of possible variations in climatic circumstances, subfloor compositions and layer thickness.

Consumption:
2.7-4 kg/m², depending on the smoothness of the subfloor and type of tile.

Substrate:
  • The subfloor must have a good tensile and compression strength. The subfloor should also be smooth, dry and free from grease, dirt and dust, according to the requirements of DIN 18 352.
  • When using the adhesive outdoors apply two layers of 730 Isoflex. Also remove all old ceramic finishing.
  • Prime moisture-sensitive or absorbent subfloors e.g. gypsum-based walls wit 099 Dispersion Primer. Apply 685 Eurocoat in the shower area to attain an impervious layer between the tile adhesive and subfloor.
  • Impervious surfaces, like existing tile work, degrease with 014 Euroclean. Thereafter let the surface dry sufficiently. Prime with 051 Europrimer Quartz or 044 Europrimer Multi.
  • For calcium sulphate (anhydrite) self-levelling anhydrite floors subfloors use 725 Alphycol.
  • In advance always seek our technical data sheets. In doubt about the application ask for technical advice. 


User manual:
  • Add 25 kg of 720 Unicol to 5-5.5 litres of cool and clean tap water and stir the mortar for 1 minute, by using an electric stirrer (approx. 600 rpm), to a smooth and homogeneous mixture.
  • After stirring wait for a few minutes, stir once again and apply the adhesive on the subfloor with the recommended adhesive spreader (see spreading capacity/notched spreader).
  • Press the tiles within 15 to 20 minutes with a shuffling movement into the adhesive. Check regularly to ensure that the back of the tile is in full contact with the adhesive. Remove excess adhesive immediately from the joints.
  • Apply the mixed adhesive within 60 minutes. Do not add extra water!
  • Under normal circumstances, i.e. a temperature of 20 °C and a relative humidity of 65%, the joints may be filled after minimum 24 hours.

Spreading capacity/notched spreader for powder tile adhesives:

The smoothness of the subfloor and type of tile are determining for the adhesive spreader to be used. Selection of the notched spreader should be made in such way that a minimum adhesive contact of 80% is guaranteed (equally divided over the back of the tile). For outdoor purposes or large sized wall tiles this contact must be 100%. Also counts for heavy-duty indoor floors, e.g. store and warehouse floors. Check the adhesive contact regularly.

Notched spreader no. 13, 8x8 mm : Spreading capacity approx. 2.7 kg/m²
Notched spreader no. 14, 10x10 mm : Spreading capacity approx. 3.5 kg/m²
Notched spreader no. 15 : Spreading capacity approx. 4 kg/m²




Quality and guarantee

Environment and health

Safety and environment : Safety data sheets of Forbo Eurocol products according to EEG-guideline 91/155.
MSDS : For extensive information about safety and environment we refer to our website www.eurocol.nl.





Articles

ArticleDefinitionPackagingEAN-code
720Unicol25 kg bag8 710345 720106