• Stable, very high load-bearing, fast curing and fast walkable, cementitiously repairing compound.
• For repairing and levelling stairs and landings.
• For filling screed break-outs, holes and deeper unevenness.
• For shaping edges, transitions and slopes.
• For filling and smoothing joints of fully bonded, approved Eurocol decoupling boards (e.g. 823 Eurofloor Reno).
• Applicable in layer thickness up to 50 mm. On decoupling boards (e.g. 823 Eurofloor Reno) up to 10 mm.
• Well extendable towards "zero" mm layer thickness.
• Stable and smooth adjustable by adding water.
• Stretchable up to 30 % with 846 Europlan Sand for layer thickness over 10 mm.
• The product can be used on underfloor heating and is suitable for use with chair castors according to DIN EN 12529.
• For interior use.
• Very low emission laying material, certified according to EMICODE EC 1 Plus.
• Declared by baubook, "ecological building product".
• Blue Angel UZ113.

• For levelling and repairing steps and smaller floor areas.
• For filling cracks, holes etc. in cement-based floors. 

• 940 Europlan Quick can be applied on any type of stony subfloor that is rigid and has a good tensile and compression strength. The subfloor should also be clean, permanently dry and free from grease and dirt, according to the requirements of BS 8203 or DIN 18 365/DIN 18356.
• Prime smooth and impervious subfloors such as tile floors, granito, terrazzo, asphalt floors and bituminous substrates as well as old and sandpapered (water-resistant) adhesive residues with 044 Europrimer Multi/044-1 Europrimer Multi Plus/070 Europrimer Fill with a foam roller.
• Prime porous cement screeds with 044 Europrimer Multi/044-1 Europrimer Multi Plus or 049 Europrimer ABS with a lambswool roller or damp with water.
• Cracks/seams in the subfloor must be fixed with 021 Euroblock Reno in combination with 063 Eurotape or with 808 Eurojoint Connector possibly in combination with 846 Quartzsand. Alternatively with Europlan 913 Silicate sealing compound.
• Appropriately dimensioned Eurocol edge strips are to be used for rising building components.
• In advance always seek our technical data sheets. In doubt about the application ask for technical advice.

• Mix the powder in the specified quantity (see technical data) with clean, cold water using an electric mixer to form a smooth, lump-free mass. For partial quantities use approx. 0.22 - 0.24 litres of water per kg powder. Only so
  mix a lot of powder as can be processed within the working time
• Depending on the intended use, varying the amount of water can produce a mortar that is stable to smooth and easy to remove.
• Apply the ready-mix within the working time in as one operation as possible until the desired layer thickness is achieved.
• Smooth stairs or repair areas with a damp sponge after smoothing. If walkable, used gauges can also be removed.
• During the setting of the levelling compound, avoid draughts and intense sunlight.
  This can lead to a too fast withdrawal of moisture, which "burns" the filler layer, pulverizes the surface edge zone and shrinkage cracks can occur.
• When laying on underfloor heating, the heating must be kept in operation for 3 days before, during and up to 7 days after laying with a surface temperature of (18 - 22) °C.
• In case of multi-layer levelling and levelling works with self-levelling compounds, apply an intermediate coat of completely set first levelling compound before applying the second one and allow to dry.
• For application thicknesses above 5 mm, stretching with sand (grain size 1 - 3 mm) is possible. When mixing, the stretching material is added as the last component. The maximum amount of additive must not exceed 30 % of the filling compound.

Processing conditions: