• Hardelastic tying (ISO 17178), water-free, solvent-free two-component adhesive.
• Adhesive with extended processing time, highly resilient. Shear-resistant curing.
• For laying standard-compliant parquet such as strip parquet, mosaic parquet, industrial parquet (including 10 mm), standard-compliant solid floor boards (>= 15 mm thickness (thickness ratio of less than 1:10)), solid lamparquet products, multilayer parquet, panel parquet, according to floor covering manufacturer’s instructions.
• Bonding is performed on standardized cement and calcium sulphate-based screeds, poured asphalt, wood based panels and gypsum fiber boards suitable for laying parquet, Eurocol decoupling and insulating underlays (e.g. 823 Eurofloor Reno, 820/821 Eurofloor Comfort, 804 Eurofloor Reno Fleece), and on nonabsorbent subfloors (e.g. fixed and cleaned ceramic and natural stone slabs, artificial stone).
• Can also be used on sprinkled with quartz sand Eurocol reactive primers approved for its application.
• Sanding and sealing of parquet is possible after about 24 hours.
• The adhesive can be used on floor heating.
• Very low emission laying material certified according to EMICODE EC1 Plus.
• Emission-tested building product according to DIBt principles.
• For indoor use.
  
  

For laying standard-compliant parquet such as

• strip parquet,
• mosaic parquet, industrial parquet (including 10 mm),
• standard-compliant solid floor boards ≥ 15 mm thickness (thickness ratio of less than 1:10), 
• lity parkiet lamelowy (lamparkiet),
• multilayer parquet, panel parquet,
• bamboo parquet.

depending on parquet format and subfloor, 

approx. 900 - 1000 g/m² (TKB/B3), approx. 1100 - 1300 g/m² (TKB/TKB11-B15).

• The substrate must be pressure- and tension-resistant, permanently dry, free of cracks and dust, even and free of layers that reduce adhesion.
• Adhesion-reducing layers, old material residues must be removed by suitable mechanical measures in accordance with the specifications of DIN 18356.
• Old fixed floors, such as ceramic tiles, terrazzo, stone floors, metals, must be professionally cleaned and sanded matt after drying.
• Cracks or joints (except structural expansion joints) are to be closed with Eurocol grouting compounds Europlan 913 Silicate.
• To reduce adhesion problems on reaction resin primers, they should be sprinkled in excess with 846 Europlan Sand.
• When laying large-format parquet elements, it is necessary to ensure that the laying surface is even.
• In case of defects, concerns must be reported in writing.

• Before use, temper the product according to the processing conditions.
• Empty the hardener component completely into the resin component and mix homogeneously with a suitable stirrer for approx. 5 minutes, also in the wall and bottom areas of the containers. Immediately decant into a clean container and mix again.
• Apply the adhesive evenly to the substrate with a toothed strip adapted to the installation and the substrate roughness. If necessary, the toothed strip can be adjusted accordingly to achieve sufficient grooved back wetting.
• To extend the working time in the warm season, the material can be mixed, homogenised and then distributed from the container in a puddle-like manner. From the puddles the material is evenly distributed.
• When laying the parquet, do not press glue between the elements to prevent adhesive marks in the joints.
  
• Since with reaction adhesives a slight "floating" of the material to be laid cannot be avoided, the laid surface must not be walked on within the first 2 hours. If it is necessary to walk on the surface, load distribution plates must be used to avoid crushing of the adhesive.
• When working on parquet, ensure that the installed parquet is approx. 1.5 cm away from the wall.
• If necessary, the glued floor coverings must be weighted down during the entire setting time, especially in the case of long parquet elements.
• After a setting time of approx. 3 - 4 hours, roll the floor once again with a multi-section roller.
• Sanding and sealing is possible under standard conditions after setting of the adhesive. Sanding is delayed at low temperatures.

Processing conditions: 

at least 15 °C floor temperature,
at least 18°C material and room temperature,
35-75% relative humidity, recommended <65%.